请高手帮忙把下面一段中文翻译成英文作为各种动力机械的核心,柴油机性能的好坏,将直接影响各种动力机械的性能.内燃机工作时,与高温燃烧气体接触的零件受热而温度升高.如不加以适当

请高手帮忙把下面一段中文翻译成英文作为各种动力机械的核心,柴油机性能的好坏,将直接影响各种动力机械的性能.内燃机工作时,与高温燃烧气体接触的零件受热而温度升高.如不加以适当
请高手帮忙把下面一段中文翻译成英文
作为各种动力机械的核心,柴油机性能的好坏,将直接影响各种动力机械的性能.内燃机工作时,与高温燃烧气体接触的零件受热而温度升高.如不加以适当的冷却和润滑,会使内燃机过热,充气系数下降,燃烧不正常,机油变质和烧损,零件的摩擦和磨损加剧,加柴油机的功率消耗,零件工作表面烧损等引起内燃机的动力性、经济性、可靠性和耐久性全面恶化,致使柴油机无法运转.为此,本文论述了在T2100柴油机冷却及润滑系统的设计,冷却系及润滑系设计时应使系统散走的热量尽可能少些,不能使发动机冷却过度,在T2100柴油机冷却系及润滑系的零件设计时,以较高的工作温度来进行设计计算.使在保证T2100柴油机正常工作的前提下使T2100柴油机在较高的温度下工作.

请高手帮忙把下面一段中文翻译成英文作为各种动力机械的核心,柴油机性能的好坏,将直接影响各种动力机械的性能.内燃机工作时,与高温燃烧气体接触的零件受热而温度升高.如不加以适当
Mechanical forces as the core engine performance is good or bad, will have a direct impact on various dynamic mechanical properties. Engine work, and access to high temperature combustion gas and heating parts of the rise in temperature. If this is not an appropriate cooling and lubrication, will Engine overheating, inflation coefficient decline is not normal combustion, Burning oil degeneration and parts of the intensified friction and wear, plus diesel power consumption, Burning parts work surface caused the engine power, economy, reliability and durability deteriorated, Diesel resulting from operating. To this end, this paper discusses the T2100 in Diesel Engine cooling and lubrication system design cooling system and lubrication system should be designed so as casual as possible taking the heat less, not excessive engine cooling, T2100 in Diesel Engine and parts of the lubrication system design, the higher the temperature for the design. Make the T2100 Diesel ensure normal work under the condition that the T2100 Diesel high temperature work

The frame is the automobile important constituent, this article take the land breeze X-8 all-terrain vehicle frame as the object of study, through uses the ANSYS software to carry on the analysis to i...

全部展开

The frame is the automobile important constituent, this article take the land breeze X-8 all-terrain vehicle frame as the object of study, through uses the ANSYS software to carry on the analysis to it.When static analysis, uses shell and the Liang combination cell frame carries on the stress and the distortion analysis, the analysis result indicated that, its amount of deformity and in the stress value all permission scope, is satisfying the intensity request.When modality analysis, uses the Liang unit to carry on the analysis, the analysis result indicated its curving frequency and the reverse frequency all are bigger than 20 Hz, satisfies the frame the operation requirements
就是这样翻译的~~一顶不错的~~行的话别忘了加分哦

收起